Differences Between Rogers RO3010 and RO3210 High-Frequency Laminates

Both are Dk 10.2 — but RO3210 is the mechanically reinforced version, and it pays for that stiffness with a higher loss tangent, a four-fold Z-axis CTE and a looser Dk tolerance. Where each one actually wins.

Differences Between Rogers RO3010 and RO3210 High-Frequency Laminates

The Short Answer

RO3010 and RO3210 share the same dielectric constant, 10.2, and are electrically interchangeable at the design level. They are not the same board. RO3210 is a ceramic-filled PTFE reinforced with woven glass; RO3010 is the same chemistry without the glass. That single difference buys roughly 2.5 times the tensile modulus, about 17% more copper peel strength and far better behaviour on large thin panels — and it costs you loss tangent (0.0027 against 0.0022), Z-axis CTE (34 against 16 ppm/°C), thermal conductivity (0.81 against 0.95 W/(m·K)) and Dk tolerance (±0.50 against ±0.30).

So the usual framing — that RO3210 is the upgraded RO3010 — has it backwards on electrical performance. RO3210 is the mechanically upgraded version, and the electrical trade is real. Choose it when the board has to stay flat, survive assembly or hold dimensions across a large panel; stay with RO3010 when loss, hole reliability or Dk consistency is what limits you.

A note on naming: both belong to Rogers’ ceramic-filled PTFE families — RO3010 in the RO3000 series, RO3210 in the RO3200 series — and neither is an RT/duroid product, despite the “RT/duroid 3210 label on many distributor pages. RT/duroid is a separate line that includes 5880, 6002 and 6010.

Datasheet Comparison

Property (typical)RO3010RO3210
SeriesRO3000RO3200
Woven glassNoYes
Dk, process @ 10 GHz10.2 ± 0.3010.2 ± 0.50
Dk, design @ 8–40 GHz11.210.8
Df @ 10 GHz0.00220.0027
CTE X / Y / Z13 / 11 / 1613 / 13 / 34
Tensile modulus≈ 1,500 MPa≈ 3,570 – 3,990 MPa
Thermal conductivity0.95 W/(m·K)0.81 W/(m·K)
Copper peel, 1 oz9.4 lb/in11.0 lb/in
Water absorption0.05%< 0.10%
Decomposition (Td)500 °C500 °C
Density2.8 g/cm³3.0 g/cm³

Read down that table and the pattern is clear: the rows where RO3210 wins are all mechanical, and the rows where RO3010 wins are all electrical or thermal. That is the entire decision.

Same Dk, Different Tolerance

The nominal dielectric constant is identical, so a first-pass layout done at 10.2 transfers between the two. Two things break that convenience in practice.

First, the tolerance: ±0.30 for RO3010 against ±0.50 for RO3210. On a narrowband design that is absorbed by tuning. On a broadband component — a 2–18 GHz coupler, a wideband antenna — a 10% Dk spread moves the upper band edge enough to require retuning, and the looser grade is the one that will surprise you across production lots.

Second, and more subtle, the design Dk differs even though the process value does not: 11.2 for RO3010 and 10.8 for RO3210 over 8–40 GHz. Process Dk is a single-point measurement at 10 GHz; design Dk averages the dispersion across the band and is what a broadband model should use. If you are moving a working wideband design from one laminate to the other, re-run the model with the design Dk rather than copying line widths — the difference is about 4% in electrical length, which on a multi-section filter is enough to lose the match.

Loss: RO3010 Is the Quieter Board

At 10 GHz, RO3010’s dissipation factor is 0.0022 and RO3210’s is 0.0027 — roughly 19% lower on RO3010, or 23% higher on RO3210 depending on which way you divide. For a circuit of the same electrical length, that difference passes straight into insertion loss, because total dielectric loss for a fixed electrical length depends only on Df (the 1/√Dk length scaling cancels the √Dk attenuation scaling).

Where it matters: a high-Q filter, a low-noise amplifier input, a long corporate feed, or anything above about 20 GHz where the loss budget is already tight. Where it does not: a short interconnect, a patch antenna feed, or a power amplifier where the active device dominates. Note also that the woven glass in RO3210 introduces a periodic Dk variation the non-woven RO3010 does not have — usually negligible below 10 GHz, but at millimeter-wave it can shift a resonant frequency slightly depending on where the trace sits relative to the weave.

CTE: the Number Nobody Expects

This is where the datasheets contradict intuition. Adding woven glass to a laminate usually improves dimensional stability, and RO3210 does hold its in-plane dimensions better — but its Z-axis CTE is 34 ppm/°C against 16 for RO3010. More than double.

That matters because Z-axis expansion is what strains a plated through hole. On a 1.5 mm board through a 200 °C excursion, RO3010 expands about 4.8 µm in the Z direction and RO3210 about 10.2 µm — the copper barrel has to absorb the difference, and over repeated thermal cycles that is where barrel cracks start. RO3010’s 13/11/16 profile is one of its headline features: all three axes sit close to copper at 17 ppm/°C, which is unusual for a material this heavily filled.

Practical rule: if the design has thick boards, many lamination cycles, or a thermal-cycling qualification with hole-reliability criteria, RO3010 is the safer of the two on that axis alone. If the board is thin, the through-holes are short and the risk is instead handling damage or warpage, RO3210’s stiffness wins.

Stiffness: Where RO3210 Earns Its Place

The tensile modulus tells the story: about 1,500 MPa for RO3010 against roughly 3,570–3,990 MPa for RO3210, depending on direction. That is a factor of about 2.4 to 2.7, and it changes how the material behaves long before it reaches the electrical test.

Concretely: a 0.254 mm core of RO3010 on a 400 mm panel is floppy enough that handling, registration and solder-paste printing all become the yield limit; the same core in RO3210 stays flat. That is exactly why the RO3200 series exists — Rogers positions it as an extension of the RO3000 family with improved mechanical stability, not as an electrical upgrade. Copper peel strength points the same way, 11.0 against 9.4 lb/in, which buys margin on assemblies that see mechanical stress or repeated rework.

The trade is not free: the glass also raises density to 3.0 g/cm³, slightly increases water absorption, and drops thermal conductivity from 0.95 to 0.81 W/(m·K). On a power design where heat leaves through the dielectric, that last figure can decide the choice on its own.

Thermal: Same Limit, Different Path

Both decompose at 500 °C on TGA and both melt in the same PTFE range. Figures in the 280–300 °C range that circulate as “thermal weight loss temperature for these grades do not describe decomposition; they read as glass-transition numbers carried over from epoxy systems, and PTFE has no glass transition of that kind. Neither material is limited by its polymer at any temperature a PCB assembly will see.

The meaningful difference is conductivity: 0.95 W/(m·K) for RO3010 against 0.81 for RO3210, both several times FR-4. On a high-power amplifier, RO3010 moves heat out through the dielectric faster; RO3210’s advantage is instead that a stiffer board stays in contact with a heatsink or chassis more reliably. Which effect dominates depends on whether your thermal path is through the board or through the mounting.

What Online Comparisons Get Wrong

This pair is one of the worst-served comparisons on the web, because the two laminates are frequently described with the wrong Dk, the wrong loss ranking, and an invented thermal hierarchy. Four values to check before trusting any table.

ClaimActual
RO3010 Dk is 9.210.2 ± 0.30 — identical to RO3210
RO3010 Df is 0.00320.0022
RO3210 Df is 0.00250.0027
Thermal weight loss 300 °C vs 280 °CBoth Td 500 °C; the 280–300 °C figures are not decomposition data

The Dk error is the costly one. A designer who accepts 9.2 for RO3010 will compute resonators about 5% long and a matching network that will not tune — and the error looks like a fabricator problem rather than a data problem, which is how it survives into a second prototype.

Choosing Between Them

If this describes your buildChooseBecause
Large panel, thin core, warpage riskRO32102.5× the modulus keeps it flat
Hybrid stack-up with FR-4 layersRO3210Glass-reinforced construction matches better in rigidity
Thick board, thermal cycling, hole reliabilityRO3010Z-axis CTE 16 vs 34 ppm/°C
High-Q filter, low-noise front endRO3010Df 0.0022 vs 0.0027 and no weave effect
Broadband, Dk consistency across lotsRO3010±0.30 tolerance against ±0.50
Power stage, heat through the boardRO30100.95 vs 0.81 W/(m·K)
Cost-driven volume, moderate electrical demandRO3210Positioned as the economically priced option

If neither fits, the next step is a different Dk rather than a different reinforcement. RO3006 at Dk 6.15 halves the size penalty with a lower loss tangent, and RO3003 at Dk 3.00 is the family’s loss leader when area is not the constraint.

Availability and Process

Both run on standard PTFE process: sodium-naphthalene or plasma activation, PTFE-specific desmear after drilling, and enhanced electroless copper or PVD seeding before plating. Neither tolerates an FR-4 line, and RO3210 additionally needs lamination and drilling parameters set for a glass-reinforced PTFE rather than a pure one.

Availability differs. RO3010 covers the full RO3000 core range from 0.127 to 1.524 mm. RO3210 is a narrower catalogue, with roughly 0.635 mm and 1.270 mm as the working thicknesses and other builds quoted on request — worth checking before you freeze a stack-up, because a design that assumes an unusual RO3210 core may need either a bonding-film build or a switch to RO3010.

XCE PCB builds both on an in-house PTFE line: 2 to 72 layers, impedance controlled to ±10% and verified by TDR coupons on the production panel, panels up to 600 × 1200 mm, 80+ engineers and more than 10,000 delivered projects, with samples in as fast as 24 hours when the laminate is in stock. For the datasheet-level detail behind these numbers, see the RO3010 parameter breakdown.

Frequently Asked Questions

What is the difference between Rogers 3010 and 3210?
Both are Dk 10.2 ceramic-filled PTFE laminates. RO3210 adds woven glass reinforcement, which raises tensile modulus from about 1,500 MPa to roughly 3,600–4,000 MPa and improves flatness on large thin panels. In exchange it has a higher loss tangent (0.0027 vs 0.0022), a much higher Z-axis CTE (34 vs 16 ppm/°C), lower thermal conductivity (0.81 vs 0.95 W/(m·K)) and a looser Dk tolerance (±0.50 vs ±0.30).
Is RO3010 a direct replacement for RO3210?
Electrically, yes — the process Dk is the same 10.2. But the design Dk differs (11.2 for RO3010, 10.8 for RO3210 over 8–40 GHz), so a broadband design should be re-simulated rather than copied. Mechanically the substitution is not neutral: RO3210 is roughly 2.5 times stiffer, and RO3010 has half the Z-axis CTE.
Which has lower loss, RO3010 or RO3210?
RO3010, at Df 0.0022 against 0.0027 at 10 GHz — about 19% lower. Because total dielectric loss at a fixed electrical length depends only on Df, that difference appears directly in insertion loss on high-Q or long-path circuits.
Why does RO3210 have a higher Z-axis CTE than RO3010?
The woven glass constrains in-plane expansion but does not constrain the through-thickness direction the same way. RO3010 is formulated so all three axes sit near copper at 17 ppm/°C — 13, 11 and 16 ppm/°C. RO3210 is 13, 13 and 34 ppm/°C, so its Z-axis expansion is more than double.
Is RO3210 more expensive than RO3010?
Usually comparable to slightly higher, but the two are not far apart and price moves with thickness and volume. Rogers positions the RO3200 series as economically priced for volume manufacturing, so for large orders RO3210 can be the cheaper route despite the added glass.
Can XCE PCB build both RO3010 and RO3210 with impedance control?
Yes. Both run on our in-house PTFE line for 2 to 72 layers, impedance controlled to ±10% and verified by TDR coupons on the production panel, panels up to 600 × 1200 mm, with samples in as fast as 24 hours when material is in stock.
RF & Microwave PCB Fabrication

RO3010 or RO3210 — Need the Right One Built?

Send us your Gerber files and requirements for a manufacturability review and a tailored quotation.

2–72 layers ±10% impedance tolerance Manufacturing since 2009